Search

Schlüter-TREP-G/-GL  Replacement slip-resistant tapes and end caps

  • Schlüter-TREP-G-B/KB is a self-adhesive tape (wide, slip resistance class R11) as a replacement for the stair nosing profiles TREP-G-B and -GK-B
  • Schlüter-TREP-GL-B/KB is a self-adhesive tape (wide, slip resistance class R10) as a replacement for the stair nosing profiles TREP-GL-B and -GK-B
  • Schlüter-TREP-G-B/EK are wide end caps made of brushed stainless steel V2A for the stair nosing profiles TREP-G-B and -GL-B
  • Schlüter-TREP-G-S/KB is a self-adhesive tape (narrow, slip resistance class R11) as a replacement for the stair nosing profiles TREP-G-S and -GK-S
  • Schlüter-TREP-GL-S/KB is a self-adhesive tape (narrow, slip resistance class R10) as a replacement for the stair nosing profiles TREP-GL-S and -GK-S
  • Schlüter-TREP-G-S/EK are narrow end caps made of brushed stainless steel V2A for the stair nosing profiles TREP-G-S and -GL-S
Where to buyData sheet
Product image TREP-G/-GL 1©Schlüter-Systems KG
Cross-section drawing TREP-G/-GL 1©Schlüter-Systems KG
Cross-section drawing TREP-G/-GL 2©Schlüter-Systems KG
Cross-section drawing TREP-G/-GL 3©Schlüter-Systems KG
zoom_out_map search
Product image TREP-G/-GL 1
Cross-section drawing TREP-G/-GL 1
Cross-section drawing TREP-G/-GL 2
Cross-section drawing TREP-G/-GL 3
 
 
 
 
 
 
 
 
 
 
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     
  •  
     
     
     
     
     
     
     
     
     
     

General product information

How to install this product

Changing the slip-resistant tread

When changing the slip-resistant tread, ensure the surrounding temperature is at least 10 °C.

  1. Remove all residue of the previous self-adhesive tape.
  2. Prior to attaching the new tape, clean the surface of the profile with a solvent.
  3. Peel back approx. 5 cm of the protective liner and position the self-adhesive tape on the surface of the profile. Avoid touching the adhesive with your fingers.
  4. Peel the protective liner back further and gradually install the full length of the tape.
  5. Use a rubber roller to firmly press the self-adhesive tape into place. Always begin from the centre and roll toward the edges.

Downloads

DownloadSelection
Schlüter-TREP-G /-GL and /-GK /-GLK | Product data sheet 3.5
Product data sheet - © Schlueter-Systems
PDF – 1.06 MB