Search

Schlüter-DITRA-HEAT-E-HK  Electrical heating cable for the DITRA-HEAT-E system

The electrical heating cable Schlüter-DITRA-HEAT-E-HK is installed in the uncoupling mat Schlüter-DITRA-HEAT and is used for applications in floor and wall assemblies. It is available in lengths from 4 to 244 metres. Since our systems are certified for waterproofing, the heating cables are approved for use in bathrooms and wetrooms.

Note: Heating cables must not be shortened.
When selecting the heating cable, please note that the product table indicates the heated space in m², not the room size. To determine the heated space, deduct unheated zones such as perimeter areas and storage space from the room size.

Where to buyData sheet
Product image DITRA-HEAT-E-HK 1©Schlüter-Systems KG
zoom_out_map search

Filter settings

  • Graphite black
  • 1,350
  • 150
  • 1,700
  • 2,050
  • 225
  • 2,400
  • 2,700
  • 300
  • 3,050
  • 375
  • 450
  • 50
  • 525
  • 600
  • 675
  • 750
  • 85
  • DHE HK 107
    Colour/surface
    not available
    Power [W]
    1,350
  • DHE HK 12
    Colour/surface
    not available
    Power [W]
    150
  • DHE HK 136
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    1,700
  • DHE HK 164
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    2,050
  • DHE HK 17
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    225
  • DHE HK 192
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    2,400
  • DHE HK 216
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    2,700
  • DHE HK 23
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    300
  • DHE HK 244
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    3,050
  • DHE HK 29
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    375
  • DHE HK 35
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    450
  • DHE HK 4
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    50
  • DHE HK 41
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    525
  • DHE HK 47
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    600
  • DHE HK 53
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    675
  • DHE HK 59
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    750
  • DHE HK 6
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    85
  • DHE HK 71
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    not available
  • DHE HK 83
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    not available
  • DHE HK 95
    Colour/surface
    Image of undefined
    Graphite black
    Power [W]
    not available

General product information

What this product does

In floor areas, the heating cables can be installed immediately after adhering DITRA-HEAT, using a minimum spacing of 9 cm (every third stud ≙ 136 W/m²).

For wall installation, the heating cables are installed once an adequate adhesive bond has been reached. The installation spacing is either 6 cm (around every second stud ≙ 200 W/m²) or 9 cm (every third stud ≙ 136 W/m²). The use of mats is recommended for wall assemblies.

Use the cable tester Schlüter-DITRA-HEAT-E-CT to measure the resistance of the electrical heating cables DITRA-HEAT-E-HK and the remote sensors supplied with DITRA-HEAT-E thermostats. The testing device should be used to monitor the resistance of the heating cables during the entire installation phase and alerts the installer with an acoustic signal in the event of damage. The cable tester automatically shuts down 60 minutes after the last key activation (values will not be saved).